Fujikura FSM-80S+ Fiber Fusion Splicer Kit

The FSM-80S is core-to-core alignment single fiber splicer succeeding to FSM-60S. In addition to ruggedized concept, which 60S created, the 80S has a series of new features, such as "Automated wind-protector and tube-heater" for quicker splicing cycle as well as fewer operation steps, "innovative ca

Specifications：

Fujikura FSM-80S+ Fusion Splicer Kit


The FSM-80S is core-to-core alignment single fiber splicer succeeding to FSM-60S. In addition to ruggedized concept, which 60S created, the 80S has a series of new features, such as "Automated wind-protector and tube-heater" for quicker splicing cycle as well as fewer operation steps, "innovative carrying-case design" for quicker preparation, "powerful Li-ion battey" for longer operation, high resolution bigger LCD monitor, and "built-in operation manuals" in various languages. Market is from backbone network installation to opto-electronics components production for quality splice.

Features:

Automated and programmable wind protector
14-second automated tube heater
Fully ruggedized for shock, dust and moisture
Li-Ion battery with 200 splices/shrinks per charge
5 mm cleave length for splice on connector or small package needs
Sheath clamp or fiber holder operation
On-board training and support videos
Internet software upgrades
Multi-function transit case with integrated workstation

Splices all known types of fibers. Fiber core alignment. Typical average splice loss for single mode cable with G.652D fiber is only 0.02 dB. Reduced splicing time - 7 seconds only. Heating time - 14 seconds only. Increased electrode lifetime - up to 3000 splicing cucles with one set, without splicing quality loss.
Battery life increased up to 200 full splicing/heating cycles. Rotary color anti-glare LCD 4.73", high contrast and vividness. Simultaneous display of X and Y axes. May splice SC, LC, MPO connectors. Automatic: wind-protective lid, heater, fiber holders.
Increased water, dust and shock resistance, may be used under severe environment conditions. Automatic arc calibration. Battery BTR-09 is included. New comfortable carrying case, optimized for quick operation start.
The case may be used as a working table. Operation manual is installed into the splicer. Software update option. 2 years of full warranty with the device replacement.



Applicable fibres

SM (ITU-T G.652 & G.657), MM (ITU-T G.651),DS (ITU-T G.653), 
NZDS (ITU-T G.655),Others

Fibre Count

Single

Cladding diameter

80 to 150μm

Coating diameter

100 to 1000μm

Fibre cleaved length

5 to 16mm using Sheath Clamp A, B or 5 to13mm using FH-60-250, FH-60-900

Actual average splice loss

0.02dB with SM, 0.01dB with MM, 0.04dB with DS, 0.04dB with NZDS.

Splice time

7sec:SM FAST mode, 12sec :SM AUTO mode, 15sec:AUTO mode

Return loss

60dB or greater

Splicing modes

100 splicer modes are available

Splice loss estimate

Several types of core deformations as well as core axis offset are taken into account for accurate loss estimate.

Attenuation splice function

Intentional high splice loss of 0.1dB to 15dB (0.01dB step) can be made for an 
inline fixed attenuator

Storage of splice result

The last 2000 results to be stored in the internal memory.

Magnification

X / Y (300X magnification), or both X and Y simultaneously (160X magnification)

Viewing method

By two CMOS cameras for intersecting fiber viewing and 4.73 inches TFT colour LCD monitor

Tension test

1.96 to 2.25N

Operating condition

0-5000m above sea level, 0-95% RH and -10 to 50°C respectively.

Tube heater

Built-in auto-start tube heater with 10 heating modes and up to 20 for reference

Tube heat time

13-15sec. with FP-03 protection sleeve. Total memory of 30 heating modes are available

Applicable protection 
sleeve length

60mm, 40mm and a series of micro sleeves.

No. of splice/heating 
with battery

200 times of splicing and heat shrinking under with BTR-09

Power supply

Auto voltage selection from 100 to 240Va.c. or 10 to 15Vd.c. with ADC-18. 14.8Vd.c. with BTR-09

Terminals

USB2.0 ( Mini-B) for data and video signal transfer to PC.

Wind protection

Up to 15m/s wind velocity

Dimensions

146(W) x 159(D) x 150(H) mm

Including wind protector, monitor, and rubber protector

Excluding rubber foot

Weight

2.5 kg, with ADC-18 AC adaptor

2.7 kg, with BTR-09 battery

Electrode life

3000 arc-discharges


Item

Description

Model No.

Qty

1

Fusion Splicer

FSM-80S
with CLAMP-S70A

1 pc

2

AC adaptor/battery charger

ADC-18

1 pc

3

AC power cord

ACC-XX

1 pc

4

Spare Electrodes

ELCT2-20A

1 pair

5

Fiber Cleaver

CT-30A

1 pc

6

Battery Pack

BTR-09

1 pc

7

USB cable

USB-01

1 pc

8

Quick reference guide

M-80S/19S-E

1 pc

9

Warning and cautions

W-70-E

1 pc

10

Instruction Manual

M-70

1 pc

11

Alcohol Pot

AP-01

1 pc

12

Battery charge cord

DCC-18

1 pc

13

Carrying Case

CC-30

1 pc

14

Screw Driver

SD-01

1pc